1、雙組份打膠機B膠桶內如果要有空氣，空氣將排不出來，B泵將快速往返運動，不能向高壓泵內正常供膠，影響整個系統，因此，必須將空氣排出來。方法是：將壓盤提出從新壓入并放氣。

　　1, B glue bucket if there is air, the air will not drain out, B pump will quickly move back and forth, can not give normal glue to the high-pressure pump, affect the whole system, therefore, must exhaust the air. The method is to press the pressure plate from the new into the air.

　　2、液壓站系統的壓力，不能調的太高，要根據室內環境溫度等實際情況，調至滿足膠嘴正常出膠均勻打膠即可。打開液壓站時一定要打開膠槍?zhuān)駝tB組份管路壓力將升得很高，造成安全事故。

　　2, the hydraulic station system pressure can not be adjusted too high, according to the indoor environment temperature and other actual situation, adjust to meet the glue mouth normal glue out, even glue. When the hydraulic station is opened, the glue gun must be opened, otherwise the pressure of the B component pipeline will rise very high, which will lead to a safety accident.

　　3、定期檢查氣源，應保證使用經干燥的潔凈壓縮空氣，并定期排放分離過濾器中的積水，檢查油霧器中的油是否夠用。

　　3, regularly check the gas source, first of all should ensure the use of dry clean compressed air, and regularly discharge separation filter in the water, check the oil in the fog is enough.

　　4、若涂膠工作過程中停頓時間超過15分鐘以上時，一定要用“沖槍”。本機有報警功能，到時沒有沖膠會有蜂鳴器報警。

　　4, if the glue working process pause time more than 15 minutes, must use "punch gun"". This machine has the alarm function, when there is no glue, there will be buzzer alarm.

　　5、正常工作時不要斷氣源，如果發現斷氣源應停止工作。

　　Don't cut off the gas source, 5 normal work, if it is found that asgassource should stop working.

　　6、A膠提膠泵連續工作1分鐘以上沒有供膠停止，說明管路內有空氣，此時會報警，須打開泵上管接頭再打開A膠提膠泵，直到出膠為止，停止并接好接頭，膠槍會出現有空氣的嗶嗶爆破聲，空氣排凈就好了。

　　6, A glue gel extraction pump work for more than 1 minutes without glue stop, that air is in the pipeline, the alarm will have to open the pump pipe joint, then open the A glue rubber glue pump, until now, stop and connect the connector glue gun will appear beep sound blasting with air. The air net is good.

　　7、壓盤上的放氣閥門要保持通暢，要定期疏通和清洗。

　　7, the pressure relief valve on the pressure plate to maintain patency, regular dredging and cleaning.

　　8、由于每次沖洗混合器不會完全干凈，每次都有少量的混合膠沉積，越來越多，以致堵塞混合器通道，用一段時間后，影響出膠量和混合效果，因此要定期(聚硫膠五天，硅酮膠兩天)清洗混合器。把混合器內的混膠棒拆出，如有損壞更換新的混膠棒。若混膠棒拆不出來，可用火燒掉，注意不能損傷零件螺紋。

　　8, because every flush mixer will not completely clean, every time there is a small amount of glue mixed deposits, more and more, that blocking the channel mixer, after a period of time, influence the quantity of cement and mixing effect, so regular (five days of polysulfide rubber, silicone rubber mixer cleaning for two days). The glue mixer and mixing, the damage as the replacement of the rubber mixing rod. If the glue stick can not be removed, it can be burnt out, pay attention to not damage the parts thread.

　　9、硅酮膠B 組份遇空氣會結殼，影響泵的正常工作和管路的暢通，因此，停機時B組份膠的所有通道在泄壓后均應關閉，使B組份不得接觸空氣。

　　9, silicone rubber B components in the air will be crusts, affecting the normal operation of the pump and the smooth flow of the pipeline, therefore, downtime, all B components of the channel should be closed after the pressure relief, so that B components shall not touch the air.

　　本文的精彩內容來自雙組份打膠機詳細內容請點擊我們的官方網站:http://linshi.jncsjx.com/謝謝您的到來!

　　The wonderful content of this article comes from the two component dispenser, please click on our official website: http://linshi.jncsjx.com/, thank you for coming!