If bubbles appear during the operation of the glue machine, there must be some problems that cannot continue to work at this time, but these problems should be solved first, otherwise excessive bubbles will affect the production quality of the product. When the dual component glue filling machine is running, there are more reasons for producing bubbles. Then, as an operator, we should analyze and see what causes the foam, and then solve these problems. Today, let's briefly introduce the causes and solutions of foam.

如果使用雙組分膠水灌裝機時產生氣泡，您可以考慮是否將氣泡帶入操作過程。例如，在混合時，如果只在一個方向攪拌，很容易導致混合不均勻，并且可能會有氣泡。所以這是由混合不良引起的。這會減少氣泡的影響。

If bubbles are generated when using a two component glue filling machine, you can consider whether to bring the bubbles into the operation process. For example, when mixing, stirring in only one direction can easily lead to uneven mixing and the possibility of bubbles. So this is caused by poor mixing. This will reduce the impact of bubbles.

此外，可能存在產生氣泡的情況，即有一些需要使用氣壓的膠水灌裝機。如果氣壓合理，例如漏氣，此時可能會爆出氣泡。在這種情況下，需要檢查燃?xì)夤艿?，如果管道出現問題，則需要修理或更換。其次是溫度，這也可能導致氣泡。某些類型的膠水需要在一定的溫度范圍內使用。如果它不在這個溫度范圍內，它可能會讓一些空氣進入。

In addition, there may be situations where bubbles are generated, such as some glue filling machines that require the use of air pressure. If the air pressure is reasonable, such as a leak, bubbles may burst at this time. In this case, it is necessary to inspect the gas pipeline, and if there is a problem with the pipeline, it needs to be repaired or replaced. Next is temperature, which may also cause bubbles. Some types of glue need to be used within a certain temperature range. If it is not within this temperature range, it may allow some air to enter.

簡單介紹雙組分膠水機產生氣泡的原因及解決方法。由于不同的原因，不同類型的膠水可能會產生氣泡。例如，一些膠水可能粘度過大，內部氣體無法正常排出。因此，需要使用一些化學試劑來減少幾年的涂層，然后投入使用，這樣才能有效地避免氣泡。

Briefly introduce the causes and solutions of bubbles generated by the dual component glue machine. Due to different reasons, different types of glue may produce bubbles. For example, some adhesives may have excessive viscosity and internal gases cannot be discharged properly. Therefore, it is necessary to use some chemical reagents to reduce the coating for several years before putting it into use, in order to effectively avoid bubbles.

當我們?cè)谀z水操作中遇到氣泡時，我們應該停下來分析氣泡的根本原因，并注意在日常工作中積累一些經驗。然后，隨著時間的使用越來越長，我們可以通過經驗找到處理這種情況的好方法。例如，在填充膠時，我們經常使用樹脂，樹脂通常會在填充膠的時候添加固化劑，但如果固化劑的比例出現問題，很可能會導致內部產生氣泡。

When we encounter bubbles during glue operation, we should stop to analyze the root cause of the bubbles and pay attention to accumulating some experience in daily work. Then, as time goes by, we can find good ways to handle this situation through experience. For example, when filling the adhesive, we often use resin, and the resin usually adds a curing agent when filling the adhesive. However, if there is a problem with the proportion of the curing agent, it is likely to cause internal bubbles to form.